IC695NIU001 PLUS 規格

如何檢查 PACSystem 中的強制值變量

描述

檢查 PACSysterm 中的強制值變量

解決

1. 在 PACSystem 中的所有 CPU 模塊以及 IC695NIU001 模塊上，都有一個名為 I/O FORCE 的 LED。一旦 ME 中至少有一個強制位，LED 就會亮起。
2. 在系統變量中，有一個 %S0011。一旦 ME 中至少有一個強制位，該系統位將被設置。
3. 當ME與PLC聯機時，我們通過右鍵單擊目標名稱然后選擇報告在ME中找到控制器中的力報告。在這個報告中，我們可以找到強制變量的變量列表。
4. 在 SVC_REQ 塊中，可以使用命令 18 來查看 ME 中是否存在強制值。

注意：對于#OVR_PRE 參考，指示一個或多個覆蓋是否處于活動狀態的%S00011 不受冗余CPU 支持且不應使用。同時，冗余 CPU 上的 LED I/O FORCE 無法顯示是否存在一個或多個覆蓋。對于冗余系統，我們可以參考方法3和4來檢查強制值。

如何設置 EGD 通信的更新超時

描述

客戶應在消費交換中設置正確的更新超時值

解決

對于 RX3i 和 ENIU(IC695NIU001) 應用，消費者的更新超時應至少是生產周期的 3 倍 + 2mSec。

請參閱 gfk-2439D 第 8-10 頁的表格，其中列出了建議的消耗超時值（注意所有超時值都是生成周期的 3x + 2mSec）。

筆記：

有關 EGD 通信的更多詳細信息，請參閱 GFK-2224 PACS_Ethernet_Manual

有關以太網網絡接口單元的更多詳細信息，請參閱 GFK-2439 PACSystems RX3i 以太網 NIU 手冊

與 IC695NIU001 進行交換的超時值

描述

RX3i ENIU (IC695NIU001) 能夠?qū)⑵漭敵鲈O(shè)置為默認值或在與控制器的通信丟失時保持其狀態。這是通過使用“控制”字從控制器產生的交換來完成的。控制字定義為：

解決

控制數據格式

以太網 NIU 消耗的前 10 個字是控制數據。它們確定通信丟失時的輸出行為，并可用于清除故障。此外，如果有兩個控制器，則控制數據決定了它們中的哪一個將提供 I/O 站輸出。（有關更多信息，請參閱 GFK-2439）。

一旦通信丟失，NIU 根據控制器發送的控制字中設置的某些位來確定輸出的狀態：

在確定正在從活動控制器接收數據后，以太網 NIU 將離散和模擬輸出數據移動到 %Q 和 %AQ 表中。如果沒有可用的活動控制器，則 ENIU 根據來自一個活動控制器的控制位的指示，將零、保持狀態或默認值移動到 %Q 和 %AQ 表中。

如果 NIU 的已消費交換的 Timeout 值設置為 0，這意味著交換永遠不會超時，則由控制字確定的狀態不會在 NIU 生效。

Troubleshooting

Troubleshooting IC695NIU001

Troubleshooting information is available on IC695NIU001's website page; it also includes a datasheet user-manual and a wiring diagram.

How to Check the Forced Value Variable in PACSystem

Description

Check the forced value variable in PACSysterm

Resolution

1. On all CPU modules in PACSystem, as well as the IC695NIU001 module, there is a LED named as I/O FORCE. And the LED will turn on once there is at least one forced bit in ME.
2. In the system variable, there is one %S0011. This system bit will be set once there is at least one forced bit in ME.
3. When ME goes online with PLC, we find a Forces in controller report in ME by right clicking target name and then choosing report. In this report, we can find out the variable list for the forced variable.
4. In the SVC_REQ block, the command 18 can be used to find out whether there is forced value in ME.

Note: For the #OVR_PRE reference, %S00011, which indicates whether one or more overrides is active, is not supported by the Redundant CPU and should not be used. At the same time, the LED I/O FORCE on the redundant CPU is not available to show whether there is one or more override. For the redundant system, we can just refer to the method 3 and 4 to check the forced value.

How To Set Update Timeout For EGD Communication

Description

Customer should set the proper Update Timeout value in the consumed exchange

Resolution

The Update Timeout of the Consumer should be at least 3x the Produced Period + 2mSec, for RX3i and ENIU(IC695NIU001) application.

Refer to gfk-2439D page 8-10 for a table listing the suggested consumed timeout values (notice all timeout values are 3x + 2mSec of the produced period).

Note:

More detail information about EGD communication, please refer to GFK-2224 PACS_Ethernet_Manual

More detail information about Ethernet Network Interface Unit, please refer to GFK-2439 PACSystems RX3i Ethernet NIU Manual

Timeout Value for Consumed Exchange with IC695NIU001

Description

The RX3i ENIU (IC695NIU001) has the ability to set its outputs to Defaults or to hold their last states when communications with the controller(s) is lost. This is done via the produced exchange from the controller(s) by using "Control" words. The Control Words are defined as:

Resolution

Control Data Format

The first 10 words of data consumed by the Ethernet NIU are control data. They determine the behavior of outputs if communications are lost, and can be used to clear faults. In addition, if there are two controllers, the control data determines which of them will supply the I/O Station outputs. (See GFK-2439 for more info).

The NIU determines the states of the outputs based on certain bits being set in the Control Word(s) being sent from the Controller(s) once communications are lost:

The Ethernet NIU moves the discrete and analog output data to the %Q and %AQ tables after determining that data is being received from an active controller. If no active controller is available then ENIU moves zeros, hold last state, or default values to the %Q and %AQ tables as directed by the control bit from the last active controller.

If the Timeout value for the consumed exchange(S) at the NIU are set to a value of 0, this means that the exchange never times out then the state as determined by the Control Word does not take effect at the NIU.